/* Copyright (c) 2009-2020 ARM Limited. All rights reserved. SPDX-License-Identifier: Apache-2.0 Licensed under the Apache License, Version 2.0 (the License); you may not use this file except in compliance with the License. You may obtain a copy of the License at www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an AS IS BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License. NOTICE: This file has been modified by Nordic Semiconductor ASA. */ /* NOTE: Template files (including this one) are application specific and therefore expected to be copied into the application project folder prior to its use! */ #include #include #include "nrf.h" #include "nrf_erratas.h" #include "system_nrf9160.h" /*lint ++flb "Enter library region" */ #define __SYSTEM_CLOCK (64000000UL) /*!< nRF9160 Application core uses a fixed System Clock Frequency of 64MHz */ #define TRACE_PIN_CNF_VALUE ( (GPIO_PIN_CNF_DIR_Output << GPIO_PIN_CNF_DIR_Pos) | \ (GPIO_PIN_CNF_INPUT_Connect << GPIO_PIN_CNF_INPUT_Pos) | \ (GPIO_PIN_CNF_PULL_Disabled << GPIO_PIN_CNF_PULL_Pos) | \ (GPIO_PIN_CNF_DRIVE_H0H1 << GPIO_PIN_CNF_DRIVE_Pos) | \ (GPIO_PIN_CNF_SENSE_Disabled << GPIO_PIN_CNF_SENSE_Pos) ) #define TRACE_TRACECLK_PIN (21) #define TRACE_TRACEDATA0_PIN (22) #define TRACE_TRACEDATA1_PIN (23) #define TRACE_TRACEDATA2_PIN (24) #define TRACE_TRACEDATA3_PIN (25) #if defined ( __CC_ARM ) uint32_t SystemCoreClock __attribute__((used)) = __SYSTEM_CLOCK; #elif defined ( __ICCARM__ ) __root uint32_t SystemCoreClock = __SYSTEM_CLOCK; #elif defined ( __GNUC__ ) uint32_t SystemCoreClock __attribute__((used)) = __SYSTEM_CLOCK; #endif /* Global values used used in Secure mode SystemInit. */ #if !defined(NRF_TRUSTZONE_NONSECURE) /* Global values used by UICR erase fix algorithm. */ static uint32_t uicr_erased_value; static uint32_t uicr_new_value; #endif /* Errata are only handled in secure mode since they usually need access to FICR. */ #if !defined(NRF_TRUSTZONE_NONSECURE) static bool uicr_HFXOSRC_erased(void); static bool uicr_HFXOCNT_erased(void); #endif void SystemCoreClockUpdate(void) { SystemCoreClock = __SYSTEM_CLOCK; } void SystemInit(void) { #if !defined(NRF_TRUSTZONE_NONSECURE) /* Perform Secure-mode initialization routines. */ /* Set all ARM SAU regions to NonSecure if TrustZone extensions are enabled. * Nordic SPU should handle Secure Attribution tasks */ #if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) SAU->CTRL |= (1 << SAU_CTRL_ALLNS_Pos); #endif /* Workaround for Errata 6 "POWER: SLEEPENTER and SLEEPEXIT events asserted after pin reset" found at the Errata document for your device located at https://infocenter.nordicsemi.com/index.jsp */ if (nrf91_errata_6()){ NRF_POWER_S->EVENTS_SLEEPENTER = (POWER_EVENTS_SLEEPENTER_EVENTS_SLEEPENTER_NotGenerated << POWER_EVENTS_SLEEPENTER_EVENTS_SLEEPENTER_Pos); NRF_POWER_S->EVENTS_SLEEPEXIT = (POWER_EVENTS_SLEEPEXIT_EVENTS_SLEEPEXIT_NotGenerated << POWER_EVENTS_SLEEPEXIT_EVENTS_SLEEPEXIT_Pos); } /* Workaround for Errata 14 "REGULATORS: LDO mode at startup" found at the Errata document for your device located at https://infocenter.nordicsemi.com/index.jsp */ if (nrf91_errata_14()){ *((volatile uint32_t *)0x50004A38) = 0x01ul; NRF_REGULATORS_S->DCDCEN = REGULATORS_DCDCEN_DCDCEN_Enabled << REGULATORS_DCDCEN_DCDCEN_Pos; } /* Workaround for Errata 15 "REGULATORS: LDO mode at startup" found at the Errata document for your device located at https://infocenter.nordicsemi.com/index.jsp */ if (nrf91_errata_15()){ NRF_REGULATORS_S->DCDCEN = REGULATORS_DCDCEN_DCDCEN_Enabled << REGULATORS_DCDCEN_DCDCEN_Pos; } /* Workaround for Errata 20 "RAM content cannot be trusted upon waking up from System ON Idle or System OFF mode" found at the Errata document for your device located at https://infocenter.nordicsemi.com/index.jsp */ if (nrf91_errata_20()){ *((volatile uint32_t *)0x5003AEE4) = 0xE; } /* Workaround for Errata 31 "XOSC32k Startup Failure" found at the Errata document for your device located at https://infocenter.nordicsemi.com/index.jsp */ if (nrf91_errata_31()){ *((volatile uint32_t *)0x5000470Cul) = 0x0; *((volatile uint32_t *)0x50004710ul) = 0x1; } /* Trimming of the device. Copy all the trimming values from FICR into the target addresses. Trim until one ADDR is not initialized. */ uint32_t index = 0; for (index = 0; index < 256ul && NRF_FICR_S->TRIMCNF[index].ADDR != 0xFFFFFFFFul; index++){ #if defined ( __ICCARM__ ) #pragma diag_suppress=Pa082 #endif *(volatile uint32_t *)NRF_FICR_S->TRIMCNF[index].ADDR = NRF_FICR_S->TRIMCNF[index].DATA; #if defined ( __ICCARM__ ) #pragma diag_default=Pa082 #endif } /* Set UICR->HFXOSRC and UICR->HFXOCNT to working defaults if UICR was erased */ if (uicr_HFXOSRC_erased() || uicr_HFXOCNT_erased()) { /* Wait for pending NVMC operations to finish */ while (NRF_NVMC_S->READY != NVMC_READY_READY_Ready); /* Enable write mode in NVMC */ NRF_NVMC_S->CONFIG = NVMC_CONFIG_WEN_Wen; while (NRF_NVMC_S->READY != NVMC_READY_READY_Ready); if (uicr_HFXOSRC_erased()){ /* Write default value to UICR->HFXOSRC */ uicr_erased_value = NRF_UICR_S->HFXOSRC; uicr_new_value = (uicr_erased_value & ~UICR_HFXOSRC_HFXOSRC_Msk) | UICR_HFXOSRC_HFXOSRC_TCXO; NRF_UICR_S->HFXOSRC = uicr_new_value; while (NRF_NVMC_S->READY != NVMC_READY_READY_Ready); } if (uicr_HFXOCNT_erased()){ /* Write default value to UICR->HFXOCNT */ uicr_erased_value = NRF_UICR_S->HFXOCNT; uicr_new_value = (uicr_erased_value & ~UICR_HFXOCNT_HFXOCNT_Msk) | 0x20; NRF_UICR_S->HFXOCNT = uicr_new_value; while (NRF_NVMC_S->READY != NVMC_READY_READY_Ready); } /* Enable read mode in NVMC */ NRF_NVMC_S->CONFIG = NVMC_CONFIG_WEN_Ren; while (NRF_NVMC_S->READY != NVMC_READY_READY_Ready); /* Reset to apply clock select update */ NVIC_SystemReset(); } /* Enable Trace functionality. If ENABLE_TRACE is not defined, TRACE pins will be used as GPIOs (see Product Specification to see which ones). */ #if defined (ENABLE_TRACE) // Enable Trace And Debug peripheral NRF_TAD_S->ENABLE = TAD_ENABLE_ENABLE_Msk; NRF_TAD_S->CLOCKSTART = TAD_CLOCKSTART_START_Msk; // Set up Trace pads SPU firewall NRF_SPU_S->GPIOPORT[0].PERM &= ~(1 << TRACE_TRACECLK_PIN); NRF_SPU_S->GPIOPORT[0].PERM &= ~(1 << TRACE_TRACEDATA0_PIN); NRF_SPU_S->GPIOPORT[0].PERM &= ~(1 << TRACE_TRACEDATA1_PIN); NRF_SPU_S->GPIOPORT[0].PERM &= ~(1 << TRACE_TRACEDATA2_PIN); NRF_SPU_S->GPIOPORT[0].PERM &= ~(1 << TRACE_TRACEDATA3_PIN); // Configure trace port pads NRF_P0_S->PIN_CNF[TRACE_TRACECLK_PIN] = TRACE_PIN_CNF_VALUE; NRF_P0_S->PIN_CNF[TRACE_TRACEDATA0_PIN] = TRACE_PIN_CNF_VALUE; NRF_P0_S->PIN_CNF[TRACE_TRACEDATA1_PIN] = TRACE_PIN_CNF_VALUE; NRF_P0_S->PIN_CNF[TRACE_TRACEDATA2_PIN] = TRACE_PIN_CNF_VALUE; NRF_P0_S->PIN_CNF[TRACE_TRACEDATA3_PIN] = TRACE_PIN_CNF_VALUE; // Select trace pins NRF_TAD_S->PSEL.TRACECLK = TRACE_TRACECLK_PIN; NRF_TAD_S->PSEL.TRACEDATA0 = TRACE_TRACEDATA0_PIN; NRF_TAD_S->PSEL.TRACEDATA1 = TRACE_TRACEDATA1_PIN; NRF_TAD_S->PSEL.TRACEDATA2 = TRACE_TRACEDATA2_PIN; NRF_TAD_S->PSEL.TRACEDATA3 = TRACE_TRACEDATA3_PIN; // Set trace port speed to 32 MHz NRF_TAD_S->TRACEPORTSPEED = TAD_TRACEPORTSPEED_TRACEPORTSPEED_32MHz; *((uint32_t *)(0xE0053000ul)) = 0x00000001ul; *((uint32_t *)(0xE005AFB0ul)) = 0xC5ACCE55ul; *((uint32_t *)(0xE005A000ul)) &= 0xFFFFFF00ul; *((uint32_t *)(0xE005A004ul)) = 0x00000009ul; *((uint32_t *)(0xE005A000ul)) = 0x00000303ul; *((uint32_t *)(0xE005AFB0ul)) = 0x00000000ul; *((uint32_t *)(0xE005BFB0ul)) = 0xC5ACCE55ul; *((uint32_t *)(0xE005B000ul)) &= 0xFFFFFF00ul; *((uint32_t *)(0xE005B004ul)) = 0x00003000ul; *((uint32_t *)(0xE005B000ul)) = 0x00000308ul; *((uint32_t *)(0xE005BFB0ul)) = 0x00000000ul; *((uint32_t *)(0xE0058FB0ul)) = 0xC5ACCE55ul; *((uint32_t *)(0xE0058000ul)) = 0x00000000ul; *((uint32_t *)(0xE0058004ul)) = 0x00000000ul; *((uint32_t *)(0xE0058FB0ul)) = 0x00000000ul; /* Rom table does not list ETB, or TPIU base addresses. * Some debug probes may require manual configuration of these peripherals to enable tracing. * ETB_BASE = 0xE0051000 * TPIU_BASE = 0xE0054000 */ #endif /* Allow Non-Secure code to run FPU instructions. * If only the secure code should control FPU power state these registers should be configured accordingly in the secure application code. */ SCB->NSACR |= (3UL << 10); #endif /* Enable the FPU if the compiler used floating point unit instructions. __FPU_USED is a MACRO defined by the * compiler. Since the FPU consumes energy, remember to disable FPU use in the compiler if floating point unit * operations are not used in your code. */ #if (__FPU_USED == 1) SCB->CPACR |= (3UL << 20) | (3UL << 22); __DSB(); __ISB(); #endif SystemCoreClockUpdate(); } #if !defined(NRF_TRUSTZONE_NONSECURE) bool uicr_HFXOCNT_erased() { if (NRF_UICR_S->HFXOCNT == 0xFFFFFFFFul) { return true; } return false; } bool uicr_HFXOSRC_erased() { if ((NRF_UICR_S->HFXOSRC & UICR_HFXOSRC_HFXOSRC_Msk) != UICR_HFXOSRC_HFXOSRC_TCXO) { return true; } return false; } #endif /*lint --flb "Leave library region" */