/** * Copyright (c) 2020, Nordic Semiconductor ASA * * All rights reserved. * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * * 1. Redistributions of source code must retain the above copyright notice, this * list of conditions and the following disclaimer. * * 2. Redistributions in binary form, except as embedded into a Nordic * Semiconductor ASA integrated circuit in a product or a software update for * such product, must reproduce the above copyright notice, this list of * conditions and the following disclaimer in the documentation and/or other * materials provided with the distribution. * * 3. Neither the name of Nordic Semiconductor ASA nor the names of its * contributors may be used to endorse or promote products derived from this * software without specific prior written permission. * * 4. This software, with or without modification, must only be used with a * Nordic Semiconductor ASA integrated circuit. * * 5. Any software provided in binary form under this license must not be reverse * engineered, decompiled, modified and/or disassembled. * * THIS SOFTWARE IS PROVIDED BY NORDIC SEMICONDUCTOR ASA "AS IS" AND ANY EXPRESS * OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY, NONINFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL NORDIC SEMICONDUCTOR ASA OR CONTRIBUTORS BE * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE * GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * */ #ifndef PCA10112_H #define PCA10112_H #ifdef __cplusplus extern "C" { #endif #include "nrf_gpio.h" // LEDs definitions for PCA10112 #define LEDS_NUMBER 4 #define LED_1 NRF_GPIO_PIN_MAP(0,13) #define LED_2 NRF_GPIO_PIN_MAP(0,14) #define LED_3 NRF_GPIO_PIN_MAP(0,15) #define LED_4 NRF_GPIO_PIN_MAP(0,16) #define LED_START LED_1 #define LED_STOP LED_4 #define LEDS_ACTIVE_STATE 0 #define LEDS_LIST { LED_1, LED_2, LED_3, LED_4 } #define LEDS_INV_MASK LEDS_MASK #define BSP_LED_0 NRF_GPIO_PIN_MAP(0,13) #define BSP_LED_1 NRF_GPIO_PIN_MAP(0,14) #define BSP_LED_2 NRF_GPIO_PIN_MAP(0,15) #define BSP_LED_3 NRF_GPIO_PIN_MAP(0,16) #define BUTTONS_NUMBER 4 #define BUTTON_1 NRF_GPIO_PIN_MAP(0,11) #define BUTTON_2 NRF_GPIO_PIN_MAP(0,12) #define BUTTON_3 NRF_GPIO_PIN_MAP(0,24) #define BUTTON_4 NRF_GPIO_PIN_MAP(0,25) #define BUTTON_PULL NRF_GPIO_PIN_PULLUP #define BUTTONS_ACTIVE_STATE 0 #define BUTTONS_LIST { BUTTON_1, BUTTON_2, BUTTON_3, BUTTON_4 } #define BSP_BUTTON_0 BUTTON_1 #define BSP_BUTTON_1 BUTTON_2 #define BSP_BUTTON_2 BUTTON_3 #define BSP_BUTTON_3 BUTTON_4 #define RX_PIN_NUMBER NRF_GPIO_PIN_MAP(0,8) #define TX_PIN_NUMBER NRF_GPIO_PIN_MAP(0,6) #define CTS_PIN_NUMBER NRF_GPIO_PIN_MAP(0,7) #define RTS_PIN_NUMBER NRF_GPIO_PIN_MAP(0,5) #define HWFC true #define NRF21540_RXEN_PIN NRF_GPIO_PIN_MAP(0,19) #define NRF21540_TXEN_PIN NRF_GPIO_PIN_MAP(0,22) #define NRF21540_PDN_PIN NRF_GPIO_PIN_MAP(0,23) #define NRF21540_MODE_PIN NRF_GPIO_PIN_MAP(0,17) #define NRF21540_ANTSEL_PIN NRF_GPIO_PIN_MAP(0,20) #define NRF21540_CS_PIN NRF_GPIO_PIN_MAP(0,21) #define NRF21540_MOSI_PIN NRF_GPIO_PIN_MAP(1,13) #define NRF21540_MISO_PIN NRF_GPIO_PIN_MAP(1,14) #define NRF21540_CLK_PIN NRF_GPIO_PIN_MAP(1,15) // serialization APPLICATION board - temp. setup for running serialized MEMU tests #define SER_APP_CTS_PIN NRF_GPIO_PIN_MAP(0,2) // UART Clear To Send pin number. #define SER_APP_SPIM0_SCK_PIN NRF_GPIO_PIN_MAP(0,27) // SPI clock GPIO pin number. #define SER_APP_SPIM0_MOSI_PIN NRF_GPIO_PIN_MAP(0,2) // SPI Master Out Slave In GPIO pin number #define SER_APP_SPIM0_MISO_PIN NRF_GPIO_PIN_MAP(0,26) // SPI Master In Slave Out GPIO pin number // serialization CONNECTIVITY board #define SER_CON_RTS_PIN NRF_GPIO_PIN_MAP(0,2) // UART Request To Send pin number. Not used if HWFC is set to false. #define SER_CON_SPIS_SCK_PIN NRF_GPIO_PIN_MAP(0,27) // SPI SCK signal. #define SER_CON_SPIS_MOSI_PIN NRF_GPIO_PIN_MAP(0,2) // SPI MOSI signal. #define SER_CON_SPIS_MISO_PIN NRF_GPIO_PIN_MAP(0,26) // SPI MISO signal. #define SER_CONN_CHIP_RESET_PIN NRF_GPIO_PIN_MAP(1,1) // Pin used to reset connectivity chip // Arduino board mappings #define ARDUINO_SCL_PIN NRF_GPIO_PIN_MAP(0, 27) // SCL signal pin #define ARDUINO_SDA_PIN NRF_GPIO_PIN_MAP(0, 26) // SDA signal pin #define ARDUINO_AREF_PIN NRF_GPIO_PIN_MAP(0, 2 ) // Aref pin #define ARDUINO_13_PIN NRF_GPIO_PIN_MAP(1, 15) // Digital pin 13 #define ARDUINO_12_PIN NRF_GPIO_PIN_MAP(1, 14) // Digital pin 12 #define ARDUINO_11_PIN NRF_GPIO_PIN_MAP(1, 13) // Digital pin 11 #define ARDUINO_10_PIN NRF_GPIO_PIN_MAP(1, 12) // Digital pin 10 #define ARDUINO_9_PIN NRF_GPIO_PIN_MAP(1, 11) // Digital pin 9 #define ARDUINO_8_PIN NRF_GPIO_PIN_MAP(1, 10) // Digital pin 8 #define ARDUINO_7_PIN NRF_GPIO_PIN_MAP(1, 8) // Digital pin 7 #define ARDUINO_6_PIN NRF_GPIO_PIN_MAP(1, 7) // Digital pin 6 #define ARDUINO_5_PIN NRF_GPIO_PIN_MAP(1, 6) // Digital pin 5 #define ARDUINO_4_PIN NRF_GPIO_PIN_MAP(1, 5) // Digital pin 4 #define ARDUINO_3_PIN NRF_GPIO_PIN_MAP(1, 4) // Digital pin 3 #define ARDUINO_2_PIN NRF_GPIO_PIN_MAP(1, 3) // Digital pin 2 #define ARDUINO_1_PIN NRF_GPIO_PIN_MAP(1, 2) // Digital pin 1 #define ARDUINO_0_PIN NRF_GPIO_PIN_MAP(1, 1) // Digital pin 0 #define ARDUINO_A0_PIN NRF_GPIO_PIN_MAP(0, 3 ) // Analog channel 0 #define ARDUINO_A1_PIN NRF_GPIO_PIN_MAP(0, 4 ) // Analog channel 1 #define ARDUINO_A2_PIN NRF_GPIO_PIN_MAP(0, 28) // Analog channel 2 #define ARDUINO_A3_PIN NRF_GPIO_PIN_MAP(0, 29) // Analog channel 3 #define ARDUINO_A4_PIN NRF_GPIO_PIN_MAP(0, 30) // Analog channel 4 #define ARDUINO_A5_PIN NRF_GPIO_PIN_MAP(0, 31) // Analog channel 5 #ifdef __cplusplus } #endif #endif // PCA10112_H