/** * Copyright (c) 2017 - 2018, Nordic Semiconductor ASA * * All rights reserved. * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * * 1. Redistributions of source code must retain the above copyright notice, this * list of conditions and the following disclaimer. * * 2. Redistributions in binary form, except as embedded into a Nordic * Semiconductor ASA integrated circuit in a product or a software update for * such product, must reproduce the above copyright notice, this list of * conditions and the following disclaimer in the documentation and/or other * materials provided with the distribution. * * 3. Neither the name of Nordic Semiconductor ASA nor the names of its * contributors may be used to endorse or promote products derived from this * software without specific prior written permission. * * 4. This software, with or without modification, must only be used with a * Nordic Semiconductor ASA integrated circuit. * * 5. Any software provided in binary form under this license must not be reverse * engineered, decompiled, modified and/or disassembled. * * THIS SOFTWARE IS PROVIDED BY NORDIC SEMICONDUCTOR ASA "AS IS" AND ANY EXPRESS * OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY, NONINFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL NORDIC SEMICONDUCTOR ASA OR CONTRIBUTORS BE * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE * GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * */ #ifndef SX1509B_H #define SX1509B_H #include "nrf_twi_sensor.h" #include "sx1509b_internal.h" #ifdef __cplusplus extern "C" { #endif /** * @brief Possible sensor addresses. */ #define SX1509B_BASE_ADDRESS_FIRST 0x3Eu #define SX1509B_BASE_ADDRESS_SECOND 0x3Fu #define SX1509B_BASE_ADDRESS_THIRD 0x70u #define SX1509B_BASE_ADDRESS_FOURTH 0x71u /** * @brief Led driver registers. */ typedef enum { SX1509B_LED_DRIVER_T_ON, SX1509B_LED_DRIVER_I_ON, SX1509B_LED_DRIVER_OFF, SX1509B_LED_DRIVER_T_RISE, SX1509B_LED_DRIVER_T_FALL } sx1509b_led_driver_set_t; /** * @brief Pin direction setting. */ typedef enum { SX1509B_PIN_DIR_OUTPUT, SX1509B_PIN_DIR_INPUT } sx1509b_pin_dir_t; /** * @brief Pin output setting. */ typedef enum { SX1509B_PIN_CLR, SX1509B_PIN_SET } sx1509b_pin_set_t; /** * @brief Pin pull setting. */ typedef enum { SX1509B_PIN_NOPULL, SX1509B_PIN_PULLDOWN, SX1509B_PIN_PULLUP } sx1509b_pin_pull_t; /** * @brief Pin sense setting. */ typedef enum { SX1509B_PIN_NOSENSE, SX1509B_PIN_SENSE_RISING, SX1509B_PIN_SENSE_FALLING, SX1509B_PIN_SENSE_BOTH } sx1509b_pin_sense_t; /** * @brief Port operation setting. * * SX1509B_PORT_WRITE - mask is written to the port. * SX1509B_PORT_CLEAR - positive bits in mask are cleared in port. * SX1509B_PORT_SET - positive bits in mask are set in port. */ typedef enum { SX1509B_PORT_WRITE, SX1509B_PORT_CLEAR, SX1509B_PORT_SET } sx1509b_port_op_t; /** * @brief Level shifter setting. */ typedef enum { SX1509B_LEVEL_OFF, SX1509B_LEVEL_A_TO_B, SX1509B_LEVEL_B_TO_A } sx1509b_level_shift_t; /** * @brief Debounce settings. */ typedef enum { SX1509B_DEBOUNCE_0_5MS, SX1509B_DEBOUNCE_1MS, SX1509B_DEBOUNCE_2MS, SX1509B_DEBOUNCE_4MS, SX1509B_DEBOUNCE_8MS, SX1509B_DEBOUNCE_16MS, SX1509B_DEBOUNCE_32MS, SX1509B_DEBOUNCE_64MS } sx1509b_debounce_t; /** * @brief Clock setting. */ typedef enum { SX1509B_CLOCK_DISABLED, SX1509B_CLOCK_EXTERNAL, SX1509B_CLOCK_INTERNAL } sx1509b_clock_t; /** * @brief Key engine sleep time setting. */ typedef enum { SX1509B_KEY_TIME_SLEEP_OFF, SX1509B_KEY_TIME_SLEEP_128MS, SX1509B_KEY_TIME_SLEEP_256MS, SX1509B_KEY_TIME_SLEEP_512MS, SX1509B_KEY_TIME_SLEEP_1S, SX1509B_KEY_TIME_SLEEP_2S, SX1509B_KEY_TIME_SLEEP_4S, SX1509B_KEY_TIME_SLEEP_8S } sx1509b_key_sleep_t; /** * @brief Key engine scan time setting. */ typedef enum { SX1509B_KEY_TIME_SCAN_1MS, SX1509B_KEY_TIME_SCAN_2MS, SX1509B_KEY_TIME_SCAN_4MS, SX1509B_KEY_TIME_SCAN_8MS, SX1509B_KEY_TIME_SCAN_16MS, SX1509B_KEY_TIME_SCAN_32MS, SX1509B_KEY_TIME_SCAN_64MS, SX1509B_KEY_TIME_SCAN_128MS } sx1509b_key_scan_t; /** * @brief Macro that defines expander module. * * @param[in] sx1509b_inst_name Name of the instance to be created. * @param[in] instance_count Number of connected expanders. */ #define SX1509B_INSTANCES_DEF_START(sx1509b_inst_name, instance_count)\ static sx1509b_instance_t sx1509b_inst_name[instance_count] /** * =============================================================================================== * @brief General expander utility functions. */ /** * @brief Function initialising expander module. * * @param[in] p_instances Pointer to expander module. * @param[in] Number of connected expanders. */ void sx1509b_init(sx1509b_instance_t * p_instances, uint8_t count); /** * @brief Function adding expander instance. * * @note Should be called for every connected expander. * Order of calls define order of pins and ports. * * @param[in] p_twi_sensor Pointer to common sensor instance. @ref NRF_TWI_SENSOR_DEF * @param[in] sensor_address Address of expander on I2C bus. * * @retval NRF_ERROR_MODULE_NOT_INITIALIZED Returned if expander module wasn't initialised * @retval NRF_ERROR_STORAGE_FULL Returned if trying to add more instances than defined. * @retval other Return error code from nrf_twi_sensor * @ref nrf_twi_sensor_write */ ret_code_t sx1509b_add_instance(nrf_twi_sensor_t * p_twi_sensor, uint8_t sensor_address); /** * @brief Function for writing current configuration to expander. * * @param[in] instance_num Number of expander, order is the same as sx1509b_add_instance calls. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no expander with given number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_cfg_write(uint8_t instance_num); /** * @brief Function for reading current configuration of expander. * * @param[in] instance_num Number of expander, order is the same as sx1509b_add_instance calls. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no expander with given number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_cfg_read(uint8_t instance_num); /** * @brief Function for setting clock configuration. * * @param instance_num Number of expander. * @param source Clock source. * @param oscio_set Oscio pin setting. True if pin is enabled. * @param oscio_freq Oscio frequency divider. Refer to expander documentation. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no expander with given number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_clock_set(uint8_t instance_num, sx1509b_clock_t source, bool oscio_set, uint8_t oscio_freq); /* * @brief Function for setting nreset and debounce time. * * @param instance_num Number of expander. * @param nreset_func Purpose of nreset pin. * @arg true Pin resets PWM/Blink/Fade counters. * @arg false Pin is equivalent to POR. * @param debounce_time Debounce time setting. * @param autoclear_nint Autoclear nint and interrupt source registers when pin data is read. * True if disabled. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no expander with such number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_misc_set(uint8_t instance_num, bool nreset_func, sx1509b_debounce_t debounce_time, bool autoclear_nint); /** * @brief Function sending software reset command to expander. * * @param instance_num Number of expander. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no expander with such number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_sw_reset(uint8_t instance_num); /** * @brief Function for setting register configuration of a single pin. * * @param[in] reg Register address, if register has two banks, address of bank B has to be used. * @param[in] pin Pin number. * @param[in] set Value to set. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no pin with such number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_pin_cfg_reg_set(sx1509b_registers_t reg, uint32_t pin, uint8_t set); /** * @brief Function for getting register configuration of a single pin. * * @param[in] reg Register address, if register has two banks, address of bank B has to be used. * @param[in] pin Pin number. * * @retval 0xFF Returned if there is no pin with given number. * @return other Pin setting value at given register. */ uint8_t sx1509b_pin_cfg_reg_get(sx1509b_registers_t reg, uint32_t pin); /** * @brief Function for setting register configuration of a port. * * @param reg Register address, if register has two banks, address of bank B has to be used. * @param port Port number. * @param mask Mask for the operating. * @param flag Operation, should the mask be written into register, clear values or set them. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no port with such number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_port_cfg_reg_set(sx1509b_registers_t reg, uint32_t port, uint8_t mask, sx1509b_port_op_t flag); /** * @brief Function for getting register configuration of a port. * * @param reg Register address, if register has two banks, address of bank B has to be used. * @param port Port number. * * @retval Register value. */ uint8_t sx1509b_port_cfg_reg_get(sx1509b_registers_t reg, uint32_t port); /** * @brief Function for updating pin data. * * @param user_cb Function to be called after pin data update is done. * * @return Return error code from nrf_twi_sensor @ref nrf_twi_sensor_reg_read */ ret_code_t sx1509b_pin_data_update(nrf_twi_sensor_reg_cb_t user_cb); /** * @brief Function for updating latch data. * * @param user_cb Function to be called after latch update is done. * * @return Return error code from nrf_twi_sensor @ref nrf_twi_sensor_reg_read */ ret_code_t sx1509b_pin_latch_update(nrf_twi_sensor_reg_cb_t user_cb); /** * @brief Function for setting long slew for given pin. * * @param pin_number Pin number. * @param set Long slew setting. * @arg true Long slew is enabled. * @arg false Long slew is disabled. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_long_slew(uint32_t pin_number, bool set); /** * @brief Function for setting low drive for given pin. * * @param pin_number Pin number. * @param set Low drive setting. * @arg true Low drive is enabled. * @arg false Low drive is disabled. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_low_drive(uint32_t pin_number, bool set); /** * @brief Function for setting open drain for given pin. * * @param pin_number Pin number. * @param set Open drain setting. * @arg true Open drain is enabled. * @arg false Open drain is disabled. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_open_drain(uint32_t pin_number, bool set); /** * @brief Function for setting polarity for given pin. * * @param pin_number Pin number. * @param set Polarity setting. * @arg true Inverted polarity. * @arg false Normal polarity. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_polarity(uint32_t pin_number, bool set); /** * @brief Function for setting debounce for given pin. * * @param pin_number Pin number. * @param set Debounce setting. * @arg true Debouncing is enabled. * @arg false Debouncing is disabled. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_debounce(uint32_t pin_number, bool set); /** * @brief Function for setting high input for given pin. * * @param pin_number Pin number. * @param set High input setting. * @arg true High input is enabled. * @arg false High input is disabled. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no pin with such number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_pin_high_input(uint32_t pin_number, bool set); /** * @brief Function for setting level shift for given pin. * * @param pin_number Pin number. * @param set Level shift setting. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_level_shifter(uint32_t pin_number, sx1509b_level_shift_t set); /** * @brief Function for setting longslew for given port. * * @param port_num Port number. * @param out_mask Long slew mask. * @param flag Port operation flag. @ref sx1509b_port_op_t * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_long_slew(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag); /** * @brief Function for setting low drive for given port. * * @param port_num Port number. * @param out_mask Low drive mask. * @param flag Port operation flag. @ref sx1509b_port_op_t * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_low_drive(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag); /** * @brief Function for setting open drain for given port. * * @param port_num Port number. * @param out_mask Open drain mask. * @param flag Port operation flag. @ref sx1509b_port_op_t * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_open_drain(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag); /** * @brief Function for setting polarity for given port. * * @param port_num Port number. * @param out_mask Polarity mask. * @param flag Port operation flag. @ref sx1509b_port_op_t * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_polarity(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag); /** * @brief Function for setting debounce for given port. * * @param port_num Port number. * @param out_mask Debounce mask. * @param flag Port operation flag. @ref sx1509b_port_op_t * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_debounce(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag); /** * @brief Function for setting high input for given port. * * @param port_num Port number. * @param out_mask High input mask. * @param flag Port operation flag. @ref sx1509b_port_op_t * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no pin with such number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_port_high_input(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag); /** * @brief Function for setting pull up for given port. * * @param port_num Port number. * @param out_mask Pull up mask. * @param flag Port operation flag. @ref sx1509b_port_op_t * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_pull_up(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag); /** * @brief Function for setting pull down for given port. * * @param port_num Port number. * @param out_mask Pull down mask. * @param flag Port operation flag. @ref sx1509b_port_op_t * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_pull_down(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag); /** * =============================================================================================== * @brief Functions compatible with nrf_gpio */ /** * @brief Function for configuring the given GPIO pin number as output, hiding inner details. * This function can be used to configure a pin as simple output with gate driving. * * @param pin_number Specifies the pin number. * * @note Sense capability on the pin is disabled as the pins are configured as output. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_cfg_output(uint32_t pin_number); /** * @brief Function for configuring the given GPIO pin number as input, hiding inner details. * This function can be used to configure a pin as simple input. * * @param pin_number Specifies the pin number. * @param pull_config State of the pin range pull resistor (no pull, pulled down, or pulled high). * * @note Sense capability on the pin is disabled and input is connected to buffer. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ ret_code_t sx1509b_pin_cfg_input(uint32_t pin_number, sx1509b_pin_pull_t pull_config); /** * @brief Function for resetting pin configuration to its default state. * * @param pin_number Specifies the pin number. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ ret_code_t sx1509b_pin_cfg_default(uint32_t pin_number); /** * @brief Function for configuring the given GPIO pin number as a watcher. Only input is connected. * * @param pin_number Specifies the pin number. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_cfg_watcher(uint32_t pin_number); // non /** * @brief Function for disconnecting input for the given GPIO. * * @param pin_number Specifies the pin number. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_cfg_input_disconnect(uint32_t pin_number); /** * @brief Function for configuring the given GPIO pin number as input, hiding inner details. * Sense capability on the pin is configurable and input is connected to buffer. * * @param pin_number Specifies the pin number. * @param pull_config State of the pin pull resistor (no pull, pulled down, or pulled high). * @param sense_config Sense level of the pin (no sense, sense low, sense high or sense both). * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ ret_code_t sx1509b_pin_cfg_sense_input(uint32_t pin_number, sx1509b_pin_pull_t pull_config, sx1509b_pin_sense_t sense_config); /** * @brief Function for configuring sense level for the given GPIO. * * @param pin_number Specifies the pin number. * @param sense_config Sense configuration. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ ret_code_t sx1509b_pin_cfg_sense_set(uint32_t pin_number, sx1509b_pin_sense_t sense_config); /** * @brief Function for setting the direction for a GPIO pin. * * @param pin_number Specifies the pin number for which to set the direction. * @param direction Specifies the direction. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ ret_code_t sx1509b_pin_dir_set(uint32_t pin_number, sx1509b_pin_dir_t direction); /** * @brief Function for setting a GPIO pin. * * Note that the pin must be configured as an output for this function to have any effect. * * @param pin_number Specifies the pin number to set. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_set(uint32_t pin_number); /** * @brief Function for clearing a GPIO pin. * * Note that the pin must be configured as an output for this * function to have any effect. * * @param pin_number Specifies the pin number to clear. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_clear(uint32_t pin_number); /** * @brief Function for toggling a GPIO pin. * * Note that the pin must be configured as an output for this * function to have any effect. * * @param pin_number Specifies the pin number to toggle. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_toggle(uint32_t pin_number); /** * @brief Function for writing a value to a GPIO pin. * * Note that the pin must be configured as an output for this * function to have any effect. * * @param pin_number Specifies the pin number to write. * * @param value Specifies the value to be written to the pin. * @arg 0 Clears the pin. * @arg >=1 Sets the pin. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_pin_write(uint32_t pin_number, sx1509b_pin_set_t value); /** * @brief Function for reading the input level of a GPIO pin. * * @note The pin must have input connected for the value * returned from this function to be valid. * Due to specifics of TWI expander, pin data must be updated first * to get current value @ref sx1509b_pin_data_update * * @param pin_number Specifies the pin number to read. * * @return 0 if the pin input level is low. Positive value if the pin is high. */ __STATIC_INLINE uint32_t sx1509b_pin_read(uint32_t pin_number); /** * @brief Function for reading the output level of a GPIO pin. * * @param pin_number Specifies the pin number to read. * * @return 0 if the pin output level is low. Positive value if pin output is high. */ __STATIC_INLINE uint32_t sx1509b_pin_out_read(uint32_t pin_number); /** * @brief Function for reading the sense configuration of a GPIO pin. * * @param pin_number Specifies the pin number to read. * * @retval Sense configuration. */ __STATIC_INLINE sx1509b_pin_sense_t sx1509b_pin_sense_get(uint32_t pin_number); /** * @brief Function for getting expander port number based on pin number. * * @retval Port number. */ __STATIC_INLINE uint8_t sx1509b_pin_port_decode(uint32_t pin_number); /** * @brief Function for setting output direction on selected pins on a given port. * * @param port_num Port number. * @param out_mask Mask specifying the pins to set as output. * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_dir_output_set(uint8_t port_num, uint8_t out_mask); /** * @brief Function for setting input direction on selected pins on a given port. * * @param port_num Port number. * @param in_mask Mask specifying the pins to set as input. * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_dir_input_set(uint8_t port_num, uint8_t in_mask); /** * @brief Function for writing the direction configuration of GPIO pins in a given port. * * @param port_num Port number. * @param dir_mask Mask specifying the direction of pins. * Bit set means that the given pin is configured as output. * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_dir_write(uint8_t port_num, uint8_t dir_mask); /** * @brief Function for reading the direction configuration of a GPIO port. * * @param port_num Port number. * * @note Returns 0 if port doesn't exist. * * @retval Pin configuration of the current direction settings. * Bit set means that the given pin is configured as output. */ __STATIC_INLINE uint8_t sx1509b_port_dir_read(uint8_t port_num); /** * @brief Function for reading the input signals of GPIO pins on a given port. * * @param port_num Port number. * * @note Returns 0 if port doesn't exist. * * @retval Port input values. */ __STATIC_INLINE uint8_t sx1509b_port_in_read(uint8_t port_num); /** * @brief Function for reading the output signals of GPIO pins of a given port. * * @param port_num Port number. * * @note Returns 0 if port doesn't exist. * * @retval Port output values. */ __STATIC_INLINE uint8_t sx1509b_port_out_read(uint8_t port_num); /** * @brief Function for writing the GPIO pins output on a given port. * * @param port_num Port number. * @param value Output port mask. * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_out_write(uint8_t port_num, uint8_t value); /** * @brief Function for setting high level on selected GPIO pins of a given port. * * @param port_num Port number. * @param set_mask Mask with pins to set as logical high level. * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_out_set(uint8_t port_num, uint8_t set_mask); /** * @brief Function for setting low level on selected GPIO pins of a given port. * * @param port_num Port number. * @param clr_mask Mask with pins to set as logical low level. * * @return Return error code from port config set @ref sx1509b_port_cfg_reg_set */ __STATIC_INLINE ret_code_t sx1509b_port_out_clear(uint8_t port_num, uint8_t clr_mask); /** * @brief Function for reading pins state of multiple consecutive ports. * * @note Due to specifics of TWI expander, pin data must be updated first * to get current value @ref sx1509b_pin_data_update * * @param start_port Index of the first port to read. * @param length Number of ports to read. * @param p_masks Pointer to output array where port states will be stored. * * @retval NRF_ERROR_INVALID_LENGTH If trying to read more ports than available. * @retval NRF_SUCCESS If operation was successful. */ ret_code_t sx1509b_ports_read(uint8_t start_port, uint32_t length, uint8_t * p_masks); /** * @brief Function for reading latch state of multiple consecutive ports. * * @note Due to specifics of TWI expander, latch data must be updated first * to get current value @ref sx1509b_pin_latch_update * * @param start_port Index of the first port to read. * @param length Number of ports to read. * @param p_masks Pointer to output array where latch states will be stored. * * @retval NRF_ERROR_INVALID_LENGTH If trying to read more ports than available. * @retval NRF_SUCCESS If operation was successful. */ ret_code_t sx1509b_latches_read(uint8_t start_port, uint32_t length, uint8_t * p_masks); /** * @brief Function for reading latch state of single pin. * * @note Due to specifics of TWI expander, latch data must be updated first * to get current value @ref sx1509b_pin_latch_update * * @param pin_number Pin number. * * @retval 0 Returned if latch is not set * @retval 1 Returned if latch is set. * @retval other Return from @ref sx1509b_pin_cfg_reg_get */ __STATIC_INLINE uint32_t sx1509b_pin_latch_get(uint32_t pin_number); /** * @brief Function for clearing latch state of a single pin. * * @param pin_number Pin number. * * @return Return error code from pin config set @ref sx1509b_pin_cfg_reg_set */ ret_code_t sx1509b_pin_latch_clear(uint32_t pin_number); /** * =============================================================================================== * @brief Led driver functions. */ /** * @brief Function enabling led driver. * * @param instance_num Number of expander instance. * @param clock_internal Sets clock source. * @arg true External clock source * @arg false Internal 2Mhz clock * @param frequency Frequency divider. * @arg 0 Led driver functionality is disabled for all IOs. * @arg Else Divider value, refer to expander documentation. * * @retval NRF_ERROR_INVALID_PARAM Returned if given instance isn't present. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_led_driver_enable(uint8_t instance_num, bool clock_internal, uint8_t frequency); /** * @brief Function for setting led driver mode. * * @param port_num Port for which mode will be set. * @param mode Led driver mode. * @arg true Logarithmic mode * @arg false Linear mode * * @retval NRF_ERROR_INVALID_PARAM Returned if given port isn't present. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_led_mode(uint8_t port_num, bool mode); /** * @brief Function for setting led driver pin times. * * @param pin_number Pin which settings will be changed. * @param on_time On time of pin. Refer to expander documentation. * @param on_intensity Intensity during on time. Between 0 and 255. * @param off_time Off time of pin. Refer to expander documentation. * @param off_intensity Intensity during off time. Between 0 and 7. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no pin with given number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_led_pin_time(uint32_t pin_number, uint8_t on_time, uint8_t on_intensity, uint8_t off_time, uint8_t off_intensity); /** * @brief Function for setting led driver pin fade characteristics. * * @param pin_number Pin which settings will be changed. * @param fade_in Fade in time of pin. Refer to expander documentation. * @param fade_out Fade out time of pin. Refer to expander documentation. * * @retval NRF_ERROR_INVALID_PARAM Returned if given pin has no fade capability, * or there is no pin with given number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_led_pin_fade(uint32_t pin_number, uint8_t fade_in, uint8_t fade_out); /** * @brief Function for enabling led driver on selected pin. * * @param pin_number Pin number. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no pin with given number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_led_pin_enable(uint32_t pin_number); /** * @brief Function for disabling led driver on selected pin. * * @param pin_number Pin number. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no pin with given number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_led_pin_disable(uint32_t pin_number); /** * @brief Function for getting led driver time on register of selected pin. * * @param pin_number Pin number. * * @retval Time on led driver register of selected pin */ uint8_t sx1509b_led_driver_get_reg(uint32_t pin_number); /** * =============================================================================================== * @brief Key Engine functions. */ /** * @brief Function enabling key engine. * * @param instance_num Number of expander. * @param rows Number of keyboard rows. * @arg < 2 Disable key engine. * @arg >= 2 Number of rows (max 8). * @param columns Number of columns (max 8). * @param sleep_time Time of inactivity before key engine enters sleep mode. * @param scan_time Scan time per column. Must be bigger than debounce time. * @param debounce_time Input debounce time. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no expander with given number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_key_engine_enable(uint8_t instance_num, uint8_t rows, uint8_t columns, sx1509b_key_sleep_t sleep_time, sx1509b_key_scan_t scan_time, sx1509b_debounce_t debounce_time); /** * @brief Function scheduling key data update. * * @param instance_num Number of expander to update. * @param user_cb Function called after key data update. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no expander with given number. * @retval other Return error code from nrf_twi_sensor @ref nrf_twi_sensor_write */ ret_code_t sx1509b_key_data_update(uint8_t instance_num, nrf_twi_sensor_reg_cb_t user_cb); /** * @brief Function returning pressed key column. * * @param instance_num Number of expander. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no expander with given number. * @retval 0xFF If no key was pressed. * @retval 0 - 7 Column number. */ uint8_t sx1509b_key_column_get(uint8_t instance_num); /** * @brief Function returning pressed key row. * * @param instance_num Number of expander. * * @retval NRF_ERROR_INVALID_PARAM Returned if there is no expander with given number. * @retval 0xFF If no key was pressed. * @retval 0 - 7 Row number. */ uint8_t sx1509b_key_row_get(uint8_t instance_num); #ifndef SUPPRESS_INLINE_IMPLEMENTATION /** * =============================================================================================== * @brief General expander inline utility functions. */ __STATIC_INLINE ret_code_t sx1509b_pin_long_slew(uint32_t pin_number, bool set) { return sx1509b_pin_cfg_reg_set(SX1509B_REG_LONG_SLEW_B, pin_number, set); } __STATIC_INLINE ret_code_t sx1509b_pin_low_drive(uint32_t pin_number, bool set) { return sx1509b_pin_cfg_reg_set(SX1509B_REG_LOW_DRIVE_B, pin_number, set); } __STATIC_INLINE ret_code_t sx1509b_pin_open_drain(uint32_t pin_number, bool set) { return sx1509b_pin_cfg_reg_set(SX1509B_REG_OPEN_DRAIN_B, pin_number, set); } __STATIC_INLINE ret_code_t sx1509b_pin_polarity(uint32_t pin_number, bool set) { return sx1509b_pin_cfg_reg_set(SX1509B_REG_POLARITY_B, pin_number, set); } __STATIC_INLINE ret_code_t sx1509b_pin_debounce(uint32_t pin_number, bool set) { return sx1509b_pin_cfg_reg_set(SX1509B_REG_DEBOUNCE_EN_B, pin_number, set); } __STATIC_INLINE ret_code_t sx1509b_pin_level_shifter(uint32_t pin_number, sx1509b_level_shift_t set) { return sx1509b_pin_cfg_reg_set(SX1509B_REG_LEVEL_SHIFTER_1, pin_number, set); } __STATIC_INLINE ret_code_t sx1509b_port_long_slew(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag) { return sx1509b_port_cfg_reg_set(SX1509B_REG_LONG_SLEW_B, port_num, out_mask, flag); } __STATIC_INLINE ret_code_t sx1509b_port_low_drive(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag) { return sx1509b_port_cfg_reg_set(SX1509B_REG_LOW_DRIVE_B, port_num, out_mask, flag); } __STATIC_INLINE ret_code_t sx1509b_port_open_drain(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag) { return sx1509b_port_cfg_reg_set(SX1509B_REG_OPEN_DRAIN_B, port_num, out_mask, flag); } __STATIC_INLINE ret_code_t sx1509b_port_polarity(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag) { return sx1509b_port_cfg_reg_set(SX1509B_REG_POLARITY_B, port_num, out_mask, flag); } __STATIC_INLINE ret_code_t sx1509b_port_debounce(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag) { return sx1509b_port_cfg_reg_set(SX1509B_REG_DEBOUNCE_EN_B, port_num, out_mask, flag); } __STATIC_INLINE ret_code_t sx1509b_port_pull_up(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag) { return sx1509b_port_cfg_reg_set(SX1509B_REG_PULL_UP_B, port_num, out_mask, flag); } __STATIC_INLINE ret_code_t sx1509b_port_pull_down(uint8_t port_num, uint8_t out_mask, sx1509b_port_op_t flag) { return sx1509b_port_cfg_reg_set(SX1509B_REG_PULL_DOWN_B, port_num, out_mask, flag); } /** * =============================================================================================== * @brief Inline functions compatible with nrf_gpio */ __STATIC_INLINE ret_code_t sx1509b_pin_cfg_output(uint32_t pin_number) { return sx1509b_pin_cfg_reg_set(SX1509B_REG_DIR_B, pin_number, SX1509B_PIN_DIR_OUTPUT); } __STATIC_INLINE ret_code_t sx1509b_pin_cfg_watcher(uint32_t pin_number) { return sx1509b_pin_cfg_input(pin_number, SX1509B_PIN_NOPULL); } __STATIC_INLINE ret_code_t sx1509b_pin_cfg_input_disconnect(uint32_t pin_number) { return sx1509b_pin_cfg_reg_set(SX1509B_REG_INPUT_DISABLE_B, pin_number, 1); } __STATIC_INLINE ret_code_t sx1509b_pin_set(uint32_t pin_number) { return sx1509b_pin_cfg_reg_set(SX1509B_REG_DATA_B, pin_number, SX1509B_PIN_SET); } __STATIC_INLINE ret_code_t sx1509b_pin_clear(uint32_t pin_number) { return sx1509b_pin_cfg_reg_set(SX1509B_REG_DATA_B, pin_number, SX1509B_PIN_CLR); } __STATIC_INLINE ret_code_t sx1509b_pin_toggle(uint32_t pin_number) { uint8_t val = sx1509b_pin_cfg_reg_get(SX1509B_REG_DATA_B, pin_number); val = !val; return sx1509b_pin_cfg_reg_set(SX1509B_REG_DATA_B, pin_number, val); } __STATIC_INLINE ret_code_t sx1509b_pin_write(uint32_t pin_number, sx1509b_pin_set_t value) { value = (value >= 1) ? 1 : 0; return sx1509b_pin_cfg_reg_set(SX1509B_REG_DATA_B, pin_number, value); } __STATIC_INLINE uint32_t sx1509b_pin_read(uint32_t pin_number) { return sx1509b_pin_cfg_reg_get(SX1509B_REG_DATA_B, pin_number); } __STATIC_INLINE uint32_t sx1509b_pin_out_read(uint32_t pin_number) { return sx1509b_pin_cfg_reg_get(SX1509B_REG_DATA_B, pin_number); } __STATIC_INLINE sx1509b_pin_sense_t sx1509b_pin_sense_get(uint32_t pin_number) { return sx1509b_pin_cfg_reg_get(SX1509B_REG_SENSE_H_B, pin_number); } __STATIC_INLINE uint8_t sx1509b_pin_port_decode(uint32_t pin_number) { return pin_number / SX1509B_INNER_NEXT_BANK; } __STATIC_INLINE ret_code_t sx1509b_port_dir_output_set(uint8_t port_num, uint8_t out_mask) { return sx1509b_port_cfg_reg_set(SX1509B_REG_DIR_B, port_num, out_mask, SX1509B_PORT_CLEAR); } __STATIC_INLINE ret_code_t sx1509b_port_dir_input_set(uint8_t port_num, uint8_t in_mask) { return sx1509b_port_cfg_reg_set(SX1509B_REG_DIR_B, port_num, in_mask, SX1509B_PORT_SET); } __STATIC_INLINE ret_code_t sx1509b_port_dir_write(uint8_t port_num, uint8_t dir_mask) { return sx1509b_port_cfg_reg_set(SX1509B_REG_DIR_B, port_num, ~dir_mask, SX1509B_PORT_WRITE); } __STATIC_INLINE uint8_t sx1509b_port_dir_read(uint8_t port_num) { return ~sx1509b_port_cfg_reg_get(SX1509B_REG_DIR_B, port_num); } __STATIC_INLINE uint8_t sx1509b_port_in_read(uint8_t port_num) { return sx1509b_port_cfg_reg_get(SX1509B_REG_DATA_B, port_num); } __STATIC_INLINE uint8_t sx1509b_port_out_read(uint8_t port_num) { return sx1509b_port_cfg_reg_get(SX1509B_REG_DATA_B, port_num); } __STATIC_INLINE ret_code_t sx1509b_port_out_write(uint8_t port_num, uint8_t value) { return sx1509b_port_cfg_reg_set(SX1509B_REG_DATA_B, port_num, value, SX1509B_PORT_WRITE); } __STATIC_INLINE ret_code_t sx1509b_port_out_set(uint8_t port_num, uint8_t set_mask) { return sx1509b_port_cfg_reg_set(SX1509B_REG_DATA_B, port_num, set_mask, SX1509B_PORT_SET); } __STATIC_INLINE ret_code_t sx1509b_port_out_clear(uint8_t port_num, uint8_t clr_mask) { return sx1509b_port_cfg_reg_set(SX1509B_REG_DATA_B, port_num, clr_mask, SX1509B_PORT_CLEAR); } __STATIC_INLINE uint32_t sx1509b_pin_latch_get(uint32_t pin_number) { return sx1509b_pin_cfg_reg_get(SX1509B_REG_INT_SRC_B, pin_number); } #endif //SUPPRESS_INLINE_IMPLEMENTATION #ifdef __cplusplus } #endif #endif // SX1509B_H